Bidirectional Power - FAQ & Known Limitations
Answers to common questions about bidirectional PAN-42 data, how the numbers behave, and what the feature doesn't cover yet.
- Getting Started
- Dashboard
- TimeView
- Energy Apps
- Alerts & Notifications
- Reports
- Administration & Settings
- Partners
- Import & Exports
- Mobile App
- Plans & Packages
- Security & Certification
- Deployment
- Hardware Manuals
- Datasheets & Specs
- Frequently Asked Questions (FAQ)
- Legal
- What’s New
- Bidirectional-Power
- Energy Star Portfolio Manager
- Panoramic AI
Table of Contents
How the Numbers Behave
- Power and Current go below zero while a device is exporting.
- Energy is net. Each Energy value is imported minus exported for that time interval. A negative value means the device exported more than it imported - not a data error.
- The Export energy counter is a running total. It's the sensor's total of all energy ever exported, so it only goes up and is always positive.
- Cost is never negative, anywhere in PowerRadar.
- Carbon is never negative. It's calculated from consumed energy only, and exporting doesn't lower it.
Frequently Asked Questions
I see a negative value - is something broken? No. On a circuit marked bidirectional, a negative Power or Current value means it was exporting at that moment, and a negative Energy value means it exported more than it imported in that interval.
Why isn't my export showing? Check that:
- bidirectional support is enabled for your site or account (contact Support if you're not sure),
- the sensor is a PAN-42,
- its Bidirectional switch is on in the Deployment Tool for all three phases (L1, L2, L3), and
- the device exported during the time range you're viewing. For Energy, a short export inside a mostly-importing interval nets out and won't make the bar go below zero. Switch to Power to see it.
How do I see how much energy was exported in a period? Use the Exported figures in the Real-time power widget's energy summary (last 24 hours, 7 days, or 30 days). For any other period, add the Export energy counter in TimeView or Manual Export and subtract the value at the start of the period from the value at the end.
Why is the Export energy counter always going up? It's a running total of all energy the sensor has ever exported - like a car's odometer - not the amount for each interval.
The Real-time power widget shows "Generation" - is that my export? No. Generation under the gauge is what your on-site generation devices (for example, PV/Solar) are producing right now. Exported in the energy summary is what actually went back to the grid. Most generated power is usually used on site, so the two numbers are different.
Why is Energy higher in Benchmarking than in TimeView? For bidirectional devices, Benchmarking counts only the energy imported from the grid, while TimeView shows the net (imported minus exported). On a site with a lot of export, Benchmarking's total will be noticeably higher.
Why isn't cost negative when I'm exporting? Cost is held at zero everywhere. PowerRadar doesn't calculate earnings from exported energy.
Is bidirectional supported in the mobile app? Yes. The PowerRadar mobile app supports bidirectional sites in the gauge, the import/export summary, Actual vs Average, the Heat Map, and Time View.
Known Limitations
Current limitations:
- Generation-category devices show as positive on their own. A device in the Generation category (for example, PV/Solar) shows as a positive value in TimeView, unless consumption is in the same view - for example, the whole site. Then it's shown below zero.
- Some cost views can undercount. On the Heat Map and in Legacy TimeView, import and export in the same hour cancel out before cost is calculated, so cost can show lower than the real import cost for a bidirectional circuit. Benchmarking works the same way over the whole selected period. Legacy TimeView doesn't show export at all. Use TimeView for bidirectional data.
- Groups that subtract a bidirectional device. In a "subtract" group, the device's net value is subtracted, so during export the group total goes up, and group Energy and Power can go below zero. The Export energy counter isn't available for groups.
- Energy Distribution doesn't show export. It shows imported energy for bidirectional devices.
- Existing Auto Export jobs don't change on their own. Jobs set up before a sensor was marked bidirectional don't include the exported energy column until you edit and save them, or create a new job.